Newest Video Review for Bowl From A Board Easy Cut System Master Pack, i.e. Lathe Mounted Disk Sander, Parting Tool with 15" Handle.

Bowl From Board Easy Cut System



Brought to you from Ron Brown's Best,LLC

This Easy Cut System eliminates about 90% of the cutting and gluing associated with traditional segmented construction. Depending on how you construct your board, the end results can be spectacular. There are many fine videos on YouTube with instructions for gluing up your starting blank.

I designed the Bowl From A Board Easy Cut System to be quick and easy to set up and use. I recommend using the narrowest parting tool you can find, typically 1/16" to 3/32". It really makes a difference in how the rings stack together. The thin parting tool will yield maximum wall thickness.

The attached video provides valuable insight for setting up and using this new system successfully. 

Although you can use boards thinner than 3/4", we believe you will have better success using material from 3/4" to 1" to begin with. After you have had some practice, experiment with thicker or thinner material. 

You can also use different angles on the same board. For Example: 1st ring cut 45 degrees, 2nd ring cut 55 degrees, third cut (base) 60 degrees will yield a bow with more of a traditional curve rather than straight sides.

NOTE: The parting tool will be perpendicular to the template. Set up as directed in the video and you will be amazed at how quick and easy it is to use your Bowl From A Board Easy Cut System. 

Each system will need a post to fit your lathe banjo. I know the specs for most common lathes so if you provide the brand and model number, that is usually all I need. If I need more info, I'll contact you.

include a 11/16" Forstner Bit matching the diameter of the blade holder tube. It should yield a perfect fit into your wooden tool handle. $6 retail value.

Customer Feedback:

Some folks tell me their banjo won’t slide far enough back to make the last cut or two. The Angle Setting Templates make this easy. Simply turn the Banjo around 180 degrees so the handle is in the rear. 

Bruce David is one of our customers who very creatively solved an issue with his Powermatic 2014. When the banjo wouldn't slide far enough back, he simply turned the jig around and used it from the other side. Brilliant thinking, Bruce! See the photos attached.

      Notice for Laguna Lathe Owners:

1)   Due to the unconventional banjo configuration, we use a knurled post so your banjo will hold it properly. This usually solves the issue. However, some customers have added a thin aluminum strip to the post for the Laguna’s banjo to obtain a firm grip on the post of the Amazing Hollowing Stabilizer. 

If you have any questions, call us at (770) 962-3821 during normal business hours Eastern time zone.

Does not include the finished bowl shown.

If you know the Brand, Model, and Swing of your lathe please enter it in the comments section of your order

Steel Guide Pin Accessory Instructions

1.   Friends, Ron Brown here, just a quick note to the many folks who have taken advantage of our new Bowl From A Board Easy Cut System.

 

 We strive to make our unique items as universal as possible and they undergo extensive testing on our own lathes before release. The only real way to discover issues is when many folks use them on their own lathes since there are hundreds of different configurations.

 

 2.   We have had some folks report that their banjos lack sufficient movement to complete the last one or two cuts and they have asked if they can simply turn the unit around and use it backward, or turn the banjo around toward the back. A couple of folks have mentioned concern about the heat generated by their parting tool and have asked for a metal alternative.

 

 3.   I am pleased to announce an extremely simple solution that we are calling the Steel Guide Pin Accessory. The release date is July 1, 2023. Units purchased before this date will be offered this free upgrade. Bowl From A Board Easy Cut Systems purchased after July, 1, 2023 will have the Guide Pin Accessory included at the time of purchase.

 

 4.   Users will simply need to drill a 3/8” diameter hole through the aluminum base plate assembly near the tip and install the Steel Guide Pin Accessory when they wish to use this rather than the original HDPE adjustable guide assembly.

 

 The width of the slot is fixed at 0.088”. It will accommodate our unique Parting Tool, and any 1/16” parting tools such as the Robert Sorby super thin parting tool. It WILL NOT ACCOMMODATE 1/8” wide parting tools unless you open the slot yourself.

 

 5.   Use either the original HDPE Adjustable Guide Pin Assembly or use the Steel Guide Pin Assembly. Don’t attempt to use them both at the same time.

 

 6.   First, remove the black HDPE Adjustable Guide Pin Assembly. Then, turn the Easy Cut System 180 degrees from normal so the beveled edge of the aluminum base points toward the rear of the lathe. Install the Steel Guide Pin Accessory with the slot turned to about 60 degrees so it points to the center of the blank and lock it firmly in place with the provided wingnut.  Use the direct read set of guide templates to align your Easy Cut System for the cut angle you wish to use. With the Steel Guide Pin Assembly, you will be able to use a parallel guideboard clamped to the bed ways for each successive cut due to the increased range of motion of your banjo. It is not necessary to move the Steel Guide Pin Accessory once properly installed.

 

  We do not supply both pin kits if you upgrade to the Premium Brass Guide Assembly.

Important! Setting PType blade cutting height.

 

Write a review

Please login or register to review

Bowl From Board Easy Cut System Get Free Parting Tool Kit Free

  • Product Code: Bowl From Board Easy Cut System
  • Availability: In Stock
  • $139.99


Available Options


Related Products

Glue Press for Bowl From Board or Segmented Rings

Glue Press for Bowl From Board or Segmented Rings

Glue Press for Bowl From A Board and Segmented Rings From Ron Brown’s Best, LLCWhy you need a G..

$0.00



More Products at Random

Glue Press Instructions ONLY

Glue Press Instructions ONLY   Description Diameter Height Price 1..

$0.00

Quad-Setting-Jig For Wood Lathe Tools 6 inch grinding wheels

Quad-Setting-Jig For Wood Lathe Tools Sets Platform Grinding Angles Quickl..

$24.99

Longworth Type 2 Basic For 18 inch & Up Lathes

The outer diameter of the disks for this chuck is 17.375" Perfect for Laguna Revo 18|36 Lathe, Je..

$293.84 $326.49

Longworth Type 2 Basic For 10 inch & Up Lathes

10" The outer diameter of the disks for this chuck is 9.375" What Is A Longworth Chuck? It is..

$161.99 $179.99